Showing results: 31 - 45 of 101 items found.
-
GVS139B -
CRYSOUND
GVS139B Polarity tester adopts pulse test, which is not affected by environmental noises. It can quickly and automatically identify the positive and negative polarity of loudspeakers, headphones, televisions, stereos, speakers, and voice coil receivers. It is suitable for production lines. Meanwhile, you can use a foot switch to switch between an external sweeper, F0, and impedance meter. It is the most suitable for the full-featured detection of speakers on production lines.
-
TS® 30 -
Fluke Networks
Recognized as the industry standard for basic test sets, the TS30 Test Set provides superior quality at an affordable price. With its high impedance Monitor for DataSafe™ operation, technicians can clip onto a line in Monitor mode without disrupting existing traffic.
-
Extech CT70 -
Extech Instruments Corporation
Circuit and wiring issues can introduce shock hazards and compromise performance of machinery and equipment. The CT70 is a GFCI and AC circuit analyzer which covers outlet load handling and outlet tester functions. AC load tester functions cover selectable loads of 12, 15, and 20 Amps; loaded and unloaded AC line voltage measurements; voltage drop/line impedance calculations; and peak line voltage. Outlet tester functions include neutral to ground voltage; hot, neutral, and ground impedance; GFCI trip time/trip current; and open or reversed wiring. The CT70 comes complete with AC test cord (standard North American 3-prong plug).
-
ST2839 -
Saluki Technology Inc.
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Chroma ATE Inc.
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
-
PP066 -
Teledyne LeCroy
The PP066 is a high-bandwidth passive probe designed for the use with the WaveMaster™ and other high-bandwidth oscilloscopes that have 50 Ω input termination. This very low capacitance probe provides an excellent solution for higher frequency applications, especially the probing of transmission lines with 20–100 Ω impedance.
-
SD -
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
Voltstik -
SensorLink
The Voltstik is a distribution voltage voltmeter designed for use on lines and in substations. This meter is employed onto a line by using a hot stick and universal chuck adapter. It is capable of measuring voltage phase to phase, and phase to ground. This high impedance instrument is an excellent choice for solving multiple problems associated with operating a medium voltage system. Its key applications are defined under three groups, safety confirmation of the voltage present, troubleshooting voltage problems, and phasing.
-
PAS 9795/DIO -
Precision Analog Systems Co.
The PAS 9795/DIO is a VME based, 80 Channel, TTL level, Digital Input / Output card. Sixty-four of the channels are arranged as eight byte wide bi-directional data ports. Each port consists of an eight-bit output data register with output enable, and an eight bit input buffer. The input buffers always monitor the state of the I/O lines, and the output data registers can either drive the I/O lines, or disconnect from the I/O by assuming a high impedance state.
-
Maury Microwave Corporation
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
7400 Series -
Venable Instruments
The Venable Model 7400 Series is the top of the line in Venable performance, supplying 4 channels for increased testing, measurement and analysis functionality. Originally designed for measuring 3-phase impedance and source and load simultaneously, the Model 7400 is a robust solution for organizations requiring high availability for high volume and/or simultaneous testing.
-
Smith Chart -
Antenna Design Associates, Inc.
Smith Chart 3.0 is a Windows-compatible software package for the analysis and design of transmission line circuits, impedance matching problems, and transistor amplifier design. Some of the new features of version 3.0 include the following:32-bit compiled code, resulting in fast executioncompletely redesigned user interfaceautomation of basic Smith chart operationsdesign of impedance matching networksplotting of up to two Smith chart data setsplot amplifier stability circlesplot amplifier constant gain circlesplot rotated 1 + jx circlelist or save data setsuse impedance, admittance, or reflection coeff.print chart or full windowcopy chart or full window to clipboardset colors of data points, cursors, backgroundonline help for Smith Chart 3.060 page User Manual, with Smith chart tutorial
-
Radio Frequency Systems
RFS offers a comprehensive product line of FM combiners to suit a wide range of applications. The balanced (or constant impedance) bandpass design offers an expandable system that is built in a modular form enabling extra stations to be added at a future date. This configuration provides state of the art performance with the best frequency response and isolation attainable.
-
NNB 21 set -
Langer EMV-Technik GmbH
The NNB 21 line impedance stabilization network is designed for measuring of grid bound interferences of a device under test according to the satndard CISPR 25/ISO 7637. It measures the RF interference, which couples into the vehicle electrical system. Measurements during the development in a frequency range from 100 kHz to 1GHz can be carried out.
